Vortex86MX+

mx-plus-cpu.jpg

Vortex86MX+

Introduction

DM&P Semiconductor Inc. is proud to provide the MPU based Vortex86MX+ x86 microprocessor. The Vortex86MX+ is an x86 compatible System-on-Chip (SoC) manufactured with a 90nm process and designed to consume less than 1 watt of electricity. It integrates various features such as multiple I/O ports (RS-232, Parallel, USB and GPIO), BIOS, Watch Dog Timer, Power Management, MTBF counter, LoC (LAN on Chip), JTAG and GPU into a single BGA chip.

Inside its 720-pin BGA package, the Vortex86MX+ packs 32kb write through 4-way L1 cache, 4-way 256KB write through/write back L2 cache, PCI rev. 2.1 32-bit bus interface at 33 MHz, DDR2, ROM controller, IPC (Internal Peripheral Controllers with DMA and interrupt timer/counter included), Fast Ethernet MAC, FIFO UART, and USB 2.0 Host and IDE controllers. With support for DOS, Windows, Linux, and other RTOSes, it provides an ideal solution for the embedded systems and communications products such as thin clients, NAT routers, home gateways, access points and tablet PCs.

Block Diagram

Features

x86 32bit Processor Core

6 stage pipe-line

Floating point unit support

Extends CPU instruction set to include Trigonometric, Logarithmic and Exponential
Implements ANSI/IEEE standard 754-1985 for binary Floating-Point Architecture

Embedded I/D Separated L1 Cache

16K I-Cache, 16K D-Cache

Embedded L2 Cache

4-wary 256KB L2 Cache
Write through or write back policy

DDRII Control Interface

6 bits data bus
DDRII clock support up to 200MHz
DDRII size support up to 1GB

IDE Controller

Support 2 channels Ultra-DMA 100 (Disk x 4)
Primary channel support SD card

LPC (Low Pin Count) Bus Interface
GPU Control Unit

VGA controller
2D Graphics engine support

MAC Controller x 1
PCI Control Interface

Up to 3 sets PCI master device
3.3V I/O

ISA Bus Interface

AT clock programmable
8/16 Bit ISA device with Zero-Wait-State
Generate refresh signals to ISA interface during DRAM refresh cycle

HDA Controller
DMA Controller
Interrupt Controller
Counter/Timers

2 sets of 8254 timer controller
Timer output is 5V tolerance I/O on 2nd Timer

Real Time Clock (Internal Mode or External Mode)

Less than 2uA (3.0V) power consumption in Internal RTC Mode while chip is power-off

FIFO UART Port x 3 (3 sets COM Port)

Compatible with 16C550/ 16C552
Default internal pull-up
Supports the programmable baud rate generator with the data rate from 50 to 115.2Kbps
Programmable character options
Support TXD_En Signal on COM1/COM2
Port 80h output data could be sent to COM1 by software programming

Parallel Port

Support SPP/EPP/ECP mod

General Programmable I/O

Supports 40 dedicated programmable I/O pins
Each GPIO pin can be individually configured to be an input/output pin
GPIO_P0~GPIO_P3 can be programmed by 8051
GPIO_P0 and GPIO_P1 with interrupt support (input/output)

USB 2.0 Host Support

Supports HS, FS and LS
4 ports

USB 1.1 Host Support

Supports FS with 3 programmable endpoint
1 port

PS/2 Keyboard and Mouse Interface Support

Compatible with 8042 controller

Redundant System Support
Speaker out
Embedded 2MB Flash

For BIOS storage

I²C bus x 2

Compliant with V2.1
Some master code (general call, START and CBUS) not support

Servo Control interface support
General Shift interface support
JTAG Interface supported for S.W. debugging
Input clock

14.318MHz
32.768KHz

Output clock

24 MHz
25 MHz
PCI clock
DDRII clock

Operating Voltage Range

Core voltage: 1.0 V ± 5%
I/O voltage: 1.8V ± 5% , 3.3 V ± 10 %

Operating temperature

0 ~ 70°C

Package Type

31x31mm, 720 Ball BGA

Special Features

ISOinChip

32 Byte one-time write Flash area containing all service tracking data. Data includes: Date codes of all major components, Model and Serial numbers, Unique serial code of SoC, Distributor code, Ship date, etc.